What is Fiber Optic Splicing?
By Colin Yao
Lights travel in optical fibers need a continuous, non-disruptive path in order to
travel a long distance without too big signal loss. But in a hundreds of kilometers fiber
link, the light signals need to be amplified, cross-connected, added or dropped and many
other processing. In these connections, two fibers are connected together as a standard
practice. This connection can be done with connectors and splicing.
Splicing is the practice of joining two fibers together without using connectors. Two
types of fiber splices exist: fusion splicing and mechanical splicing. Splicing may be
made during installation or repair.
Splices generally have lower loss and better mechanical integrity than connectors,
while connectors make system configuration much more flexible. So typically, splices are
used to connect fiber cables in outdoor applications and connectors terminate fiber cables
inside buildings.
Fusion Splicing
Fusion splicing is to use high temperature heat generated by electric arc and fuse two
glass fibers together (end to end with fiber core aligned precisely). The tips of two
fibers are butted together and heated so they melt together. This is normally done with a
fusion splicer, which mechanically aligns the two fiber ends, then applies a spark across
the fiber tips to fuse them together.
Mechanical Splicing
Mechanical splicing uses mechanical fixtures to join two fibers together end to
end(again, fiber cores are aligned precisely). Mechanical splicing join two fiber ends
either by clamping them within a structure or by gluing them together.
Single mode fiber requires much tighter tolerances than multimode fibers for splicing.
So special equipment are often required for single mode mechanical splices. This makes
single mode fiber mechanical splicing much more expensive than multimode fiber mechanical splicing.
The advantages of mechanical splicing
Mechanical splicing doesn't need costly capital equipment to work, but it does require
higher consumable costs. So for organizations that don't make a lot of splicing,
mechanical splicing is the best choice. It is also best suited for emergency repairs.
Types of mechanical splicing
1. Capillary type
In capillary type mechanical splicing, two fibers are inserted into a thin capillary
tube. The tube has a inner diameter that matches the fiber's cladding diameter. (The
fibers must first have coatings removed and cladding exposed and cleaned). These two fiber
ends are pushed inwards until they meet. Index matching gels are often inserted in the
center to reduce back reflections. The fibers are then held in place with compression or friction.
2. Ribbon V-Groove type
For multiple fiber cables such as ribbon fibers, capillary type doesn't work anymore.
Instead, fiber ribbon is put in a V-shaped groove array, with each fiber place in its own
v-groove. Two ribbon fibers are butted together in this V-groove array and then a cover
plate is applied on top. This V-groove splice is extremely useful in multifiber splicing.
3. Elastomeric type
Elastomeric splice is for lab testing or emergency fiber repairs. Very like
aforementioned V-groove type, it has a single fiber v-groove but the v-groove is made of
flexible plastic. First an index matching gel is injected into the hole, then one fiber is
inserted until it reaches about halfway. The other fiber is then inserted from the other
end until it meet the first one.
Colin Yao is an expert on fiber optic technologies and products. Learn even more about
mode conditioning cable and
mode conditioning fiber
on Fiber Optics For Sale Co. web site.
More Networking Topologies Articles:
• Understanding Basic Terms in Indoor Fiber Optic Cable Installation
• What is an Ethernet Bridge?
• Introduction to ATM (Asynchronous Transfer Mode) Networks
• Difference Between Unmanaged, Web Smart and Managed Switch
• Understanding Wireless LAN Networking
• Cisco Switching Fundamentals
• Wireless Networks
• Routing Technologies, Bandwidth Management and Traffic Shaping
• Beginners Guide to Fiber Optic Bit Error Ratio (BER) Measurement
• VPN (Virtual Private Network) headend or Concentrator
| 
About BTH
User Agreement
Privacy
Site Map
Contact
News Feeds
RSS Feed
Follow @Stephen Bucaro
Basics and Certification
